High-performance cellulose ether engineered for water retention, open time, anti-sag behavior, workability, and consistent mortar performance in cement-based and gypsum-based building material systems.
LANDERCOLL HEMC / MHEC is a water-soluble, non-ionic cellulose ether designed for drymix construction material manufacturers who need reliable, repeatable performance in tile adhesive, wall putty, skim coat, cement plaster, gypsum plaster, EIFS / ETICS mortar, masonry mortar, waterproof mortar, and repair mortar systems.
In cement-based and gypsum-based formulations, HEMC / MHEC delivers measurable improvements in water retention, open time, anti-sag behavior, troweling feel, spreading smoothness, and application consistency — making it one of the most widely used functional additives in the global drymix mortar industry.
LANDERCOLL HEMC / MHEC is a construction-focused cellulose ether product engineered for manufacturers who need reliable water retention, workability improvement, open time extension, anti-sag behavior, and consistent mortar performance across a wide range of drymix building material systems.
As a non-ionic, water-soluble cellulose ether, HEMC / MHEC is especially well-suited for cement-based and gypsum-based formulations. It influences how mortar mixes with water, how smoothly it spreads and trowels, how long it remains workable, how well it resists sagging on vertical surfaces, and how consistently it performs from batch to batch on the job site.
Different drymix products require different HEMC / MHEC grades. The right selection depends on viscosity level, water retention target, open time requirement, anti-slip performance, formulation design, and application method.
HEMC / MHEC is particularly established in tile adhesive, tile grout, wall putty, skim coat, cement render, cement plaster, gypsum plaster, masonry mortar, EIFS / ETICS mortar, waterproof mortar, repair mortar, and ready-mix dry mortar systems.
HEMC stands for Hydroxyethyl Methyl Cellulose. MHEC stands for Methyl Hydroxyethyl Cellulose. Both names refer to the same product family (CAS 9032-42-2). HEMC / MHEC is produced by chemically modifying purified natural cellulose — typically derived from wood pulp or cotton linter — through a controlled alkaline reaction with methyl chloride and ethylene oxide.
Influence solubility, thermal behavior, and surface activity of the cellulose ether in mortar systems.
Influence water retention capacity, viscosity development, and compatibility within mortar systems.
The ratio and degree of these two substitutions determine the grade's performance profile. Viscosity — typically measured at 2% aqueous solution — is the primary parameter for grade selection, ranging from below 5,000 mPa·s to above 200,000 mPa·s.
Although used at relatively low dosage levels — typically 0.1%–0.5% of the dry mix weight — HEMC / MHEC has a strong influence on mortar performance, affecting water retention, rheology, open time, and anti-sag behavior simultaneously.
Both are non-ionic methyl cellulose ethers used in construction materials, but they differ in their secondary substitution group. HPMC uses hydroxypropyl groups (–OCH₂CHOHCH₃), while HEMC / MHEC uses hydroxyethyl groups (–OCH₂CH₂OH). This structural difference affects water retention behavior, dissolution profile, and performance characteristics in specific mortar systems. In many European and international drymix construction markets, HEMC / MHEC is particularly established for tile adhesive, plaster, and EIFS / ETICS applications.
Despite dosage levels of only 0.1%–0.5%, HEMC / MHEC delivers measurable improvements across water retention, open time, anti-sag behavior, workability, and surface finish — making it one of the highest-value functional ingredients in drymix mortar formulation.
The following table provides a general technical reference for Hydroxyethyl Methyl Cellulose. Exact values vary by product grade, viscosity level, substitution type, particle size, surface treatment, and testing method. This information is intended as a formulation reference starting point, not a final product specification.
| Item | Typical Reference |
|---|---|
| Название продукта | Гидроксиэтилметилцеллюлоза / Метилгидроксиэтилцеллюлоза |
| Abbreviation | HEMC / MHEC |
| CAS No. | 9032-42-2 |
| Внешний вид | Порошок от белого до светло-белого цвета |
| Ionic Type | Неионогенные |
| Molecular Basis | Cellulose ether (modified natural cellulose) |
| Raw Material Source | Wood pulp or cotton linter |
| Растворимость | Soluble in cold water; forms a viscous, pseudoplastic solution |
| Термическая гелеобразование | Gels upon heating; re-dissolves upon cooling (thermally reversible) |
| Viscosity Range | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| Стабильность pH | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| Ключевые функции | Water retention, thickening, workability improvement, rheology control, anti-sag support |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Note: Viscosity ranges listed above are approximate references. Actual LANDERCOLL HEMC / MHEC grades should be selected according to your formulation, testing method, application environment, and required documentation. Contact our team for specific grade recommendations.
HEMC / MHEC is a multifunctional cellulose ether. In most drymix mortar applications, it contributes several performance benefits simultaneously. Below is a structured overview of its primary functions across different construction system types.
HEMC / MHEC forms a polymer network within the mortar matrix that physically restricts water migration into the substrate. This ensures sufficient water remains available for complete cement hydration or gypsum setting — supporting stronger bond development, better surface quality, and longer working time. Higher viscosity grades and higher dosage levels generally provide stronger water retention.
HEMC / MHEC makes mortar smoother, more cohesive, and easier to spread, trowel, scrape, and finish. Tile adhesive spreads more evenly with less effort. Wall putty scrapes more smoothly with fewer drag marks. Plaster and render spread more consistently across large surfaces. Finishing coats level more easily and produce better surface quality.
HEMC / MHEC extends open time by maintaining moisture within the mortar layer and slowing the rate of water loss to the substrate and to evaporation. This is critical in tile adhesive and wall putty, where insufficient open time forces installers to work in smaller sections — increasing labor time and the risk of poor bond formation. Especially important for large-format tile installation.
HEMC / MHEC builds mortar body and provides a pseudoplastic rheology profile. The mortar flows and spreads under tool pressure during application, but recovers its structure and resists movement once the tool is removed — essential for reliable vertical surface installation in wall tile adhesive, EIFS / ETICS, and repair mortar.
HEMC / MHEC solutions are pseudoplastic (shear-thinning): viscosity decreases under shear during mixing and application, and recovers at rest. In self-leveling compounds, it contributes to controlled flow without excessive separation. In machine-applied plaster, it helps maintain consistent pump pressure and spray behavior.
HEMC / MHEC improves homogeneity and batch-to-batch consistency, reducing variability between batches, operators, and environmental conditions. In wall putty, skim coat, gypsum plaster, and finishing mortar, it contributes to improved scraping behavior, leveling, and final surface quality ready for painting or decoration.
HEMC / MHEC grade selection should always begin with the target application. Different construction products require different balances of water retention, viscosity, open time, anti-sag behavior, smoothness, and surface finish quality. The table below provides a structured reference for common application-to-grade matching.
| Приложение | Recommended Grade Direction | Основные требования к характеристикам |
|---|---|---|
| Клей для плитки | High to extra-high viscosity | Water retention, open time, anti-slip, troweling feel |
| Плиточная затирка | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | Smooth filling, water retention, workability |
| Шпаклевка для стен / грунтовка | Medium to high viscosity | Smooth scraping, water retention, surface finish |
| Цементная штукатурка | Medium to high viscosity | Работоспособность, распределяемость, удержание воды |
| Гипсовая штукатурка | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | Гладкое нанесение, управление водой, консистенция |
| Кладочный раствор | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | Board life, workability, water retention |
| Самовыравнивающиеся составы | Low to medium viscosity | Controlled flow, stability, water retention |
| Морозостойкая штукатурка / ETICS | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| Водостойкий раствор | Medium to high viscosity | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| Ремонтная штукатурка | Medium to high viscosity | Anti-sag, water retention, controlled finishing |
| Изоляционная штукатурка | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | Anti-sag, open time, adhesion support |
| Сухая готовая смесь | Зависит от типа продукта | Consistency, workability, industrial production stability |
Grade direction is a starting reference. Final selection must be confirmed through laboratory testing under your specific formulation conditions — cement type, filler system, gypsum quality, ambient temperature, water quality, redispersible polymer powder content, starch ether addition, and application method can all significantly affect performance.
HEMC / MHEC dosage depends on formulation design, raw material quality, application type, target performance, ambient temperature, water quality, substrate type, and production process. The following ranges are general starting points for laboratory evaluation — not fixed usage standards.
For tile adhesive: 0.2%–0.4% is a widely referenced industry starting range. However, the optimal dosage depends on cement type, filler quality, target open time, anti-slip requirement, tile size and weight, and ambient temperature. Final dosage must always be confirmed through laboratory testing and on-site performance evaluation.
| Приложение | Typical Reference Dosage (% by weight of dry mix) |
|---|---|
| Клей для плитки | 0.2% – 0.4% |
| Плиточная затирка | 0.1% – 0.3% |
| Шпаклевка для стен / грунтовка | 0.2% – 0.5% |
| Цементная штукатурка | 0.15% – 0.4% |
| Гипсовая штукатурка | 0.1% – 0.3% |
| Кладочный раствор | 0.1% – 0.3% |
| Самовыравнивающиеся составы | 0.05% – 0.2% |
| Морозостойкая штукатурка / ETICS | 0.2% – 0.5% |
| Водостойкий раствор | 0.15% – 0.4% |
| Ремонтная штукатурка | 0.15% – 0.4% |
| Изоляционная штукатурка | 0.2% – 0.4% |
| Сухая готовая смесь | Depends on product type and performance target |
These dosage ranges are general starting points. Adjust based on testing results under your specific formulation, raw materials, application conditions, and performance targets.
Tile Adhesive · i.
01
One of the most important functional additives in tile adhesive — directly affecting the four parameters that matter most to tile installers.
Water retention prevents rapid water loss into the substrate or tile back, ensuring adequate cement hydration and bond development. Open time extension keeps the adhesive workable and bondable for longer — especially critical for large-format tile installation. Anti-slip behavior provides mortar body and cohesion to prevent tiles from sliding on vertical surfaces. Troweling feel improves smoothness and consistency during notch trowel spreading.
High to extra-high viscosity HEMC / MHEC grades are typically used, with dosage in the range of 0.2%–0.4% of the dry mix weight. Surface-treated grades are commonly preferred to prevent premature hydration during dry powder mixing, storage, and transport.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Plaster · iv.
05
Controlled water retention, smooth spreading behavior, and stable workability — for both manual and machine application.
Cement Render & Plaster — HEMC / MHEC improves mortar handling during both manual and machine application. It helps the render spread more evenly, reduces surface tearing, maintains workable consistency throughout the session, supports better surface finishing, and contributes to consistent pump behavior and spray pattern stability in machine-applied systems.
Gypsum Plaster — HEMC / MHEC helps improve water retention and workability in gypsum plaster without excessively retarding the setting process. Because gypsum systems are sensitive to set time, HEMC / MHEC grade and dosage selection must be carefully tested.
Used across all system layers to improve open time, anti-sag behavior, stable consistency, and application reliability. In adhesive mortar, extends open time for accurate insulation board placement. In base coat, provides anti-sag and smooth mesh embedding. In finishing coat, supports smooth application and surface quality.
For waterproof mortar: stable mortar consistency, smooth coating behavior, controlled water retention, and uniform application thickness on surfaces exposed to water. For repair mortar: anti-sag behavior for vertical and overhead applications, improved water retention on absorptive substrates, and better workability and finishing control during surface restoration.
For self-leveling compounds: controlled flow behavior, improved water retention reducing bleeding risk, better system stability, and smoother final surface formation. Low to medium viscosity grades at carefully controlled dosage. For ready-mix dry mortar: consistent batch-to-batch quality and reliable performance across varying site conditions.
Designed for tile adhesive formulations requiring open time extension, anti-slip performance, strong water retention, troweling comfort, and application consistency. Surface-treated grades commonly preferred for drymix tile adhesive production.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitscURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Construction · Pharma · Food · Personal care · Detergents · IndustrialcURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
Water-based paints · Coatings · Cleaners · Personal carecURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limitsBoth are non-ionic methyl cellulose ethers used in drymix construction materials and can deliver similar core functions. The choice depends on specific performance targets, regional market preferences, formulation system, raw material compatibility, and cost considerations. In many European and international drymix construction markets, HEMC / MHEC is particularly established for tile adhesive, plaster, and EIFS / ETICS. HPMC is more widely used across a broader range of industries. Neither product is universally superior — the right choice should be determined by formulation testing in your specific system.
Both HEMC / MHEC and HPMC are non-ionic methyl cellulose ethers, but they differ in their secondary substitution group: HPMC uses hydroxypropyl groups (–OCH₂CHOHCH₃) while HEMC / MHEC uses hydroxyethyl groups (–OCH₂CH₂OH). This structural difference affects water retention behavior, dissolution profile, and performance characteristics in specific mortar systems — making grade selection and formulation testing essential for determining the optimal product for your application.
LANDERCOLL HEMC / MHEC is supplied in industrial packaging suitable for transportation, storage, and production handling. Cellulose ether powders are hygroscopic — proper storage conditions help maintain powder flowability, dissolution performance, and application effectiveness throughout product shelf life.
Standard Packaging
Storage Recommendations
LANDERCOLL can provide product-related documentation to support formulation evaluation, purchasing review, technical communication, regulatory submission, and internal approval processes.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
To help our team recommend the most suitable HEMC / MHEC grade for your application, please include as much of the following information as possible when contacting us. A detailed inquiry allows us to provide a more accurate grade recommendation and support your evaluation more efficiently.
Product application (e.g., tile adhesive, wall putty, gypsum plaster, EIFS mortar) and formulation system type (cement-based, gypsum-based, or mixed system).
Current HEMC / MHEC or HPMC grade reference, if available. Main performance target — e.g., open time, water retention, anti-sag, surface finish. Application method: manual troweling, scraping, machine spraying, or pouring.
Current formulation challenge or performance gap, if applicable. Testing method or standard used, if applicable. Required quantity — sample, trial, or commercial volume.
Destination country or target market. Documentation requirements — TDS, SDS, COA, compliance documents. Timeline for evaluation or sourcing decision.
HEMC / MHEC (CAS 9032-42-2) is primarily used as a functional additive in drymix construction materials. It improves water retention, workability, open time, anti-sag performance, mortar consistency, and application behavior in tile adhesive, wall putty, skim coat, cement plaster, gypsum plaster, masonry mortar, EIFS / ETICS mortar, waterproof mortar, repair mortar, and ready-mix dry mortar systems.
Yes. HEMC (Hydroxyethyl Methyl Cellulose) and MHEC (Methyl Hydroxyethyl Cellulose) are two names for the same product family. The difference is only in naming convention — HEMC emphasizes the hydroxyethyl group first, while MHEC emphasizes the methyl group first. Both refer to the same chemical substance (CAS 9032-42-2) and are widely used in the cellulose ether and construction materials industry.
The commonly referenced CAS number for HEMC / MHEC is 9032-42-2.
In tile adhesive, HEMC / MHEC improves water retention to support cement hydration and bond strength, extends open time to give installers more working time for tile positioning, provides anti-slip behavior to prevent tiles from sliding on vertical surfaces, and improves troweling feel and application consistency. High to extra-high viscosity grades are typically used at dosages of 0.2%–0.4% of the dry mix weight.
The typical reference dosage is approximately 0.1%–0.5% by weight of the dry mix, depending on the application. For tile adhesive: 0.2%–0.4%. For wall putty and skim coat: 0.2%–0.5%. For gypsum plaster and masonry mortar: 0.1%–0.3%. Final dosage must always be confirmed through laboratory testing and job-site performance evaluation.
In wall putty and skim coat, HEMC / MHEC improves water retention to prevent rapid drying, enhances scraping smoothness and surface finish quality, improves spreading behavior and workability, and helps maintain consistent product texture throughout the application session. Medium to high viscosity grades are typically used.
Both HEMC / MHEC and HPMC are used in tile adhesive and can deliver similar core performance. Neither is universally superior. HEMC / MHEC is particularly established in European and international drymix construction markets. HPMC is more widely used across a broader range of industries. The right choice depends on your specific formulation, raw material system, performance targets, and market requirements. Formulation testing is always recommended.
Yes. HEMC / MHEC can be used in gypsum plaster and related gypsum-based systems to improve water retention, workability, smooth spreading behavior, and application consistency. However, because gypsum systems are sensitive to set time, HEMC / MHEC grade and dosage must be carefully selected and tested to avoid excessive retardation of the gypsum setting reaction.
Tile adhesive typically uses high to extra-high viscosity HEMC / MHEC, generally in the range of 60,000–200,000 mPa·s (measured at 2% aqueous solution). The exact viscosity grade depends on the formulation type, tile size and weight, required open time, anti-slip performance target, and application conditions. Final grade selection should be confirmed through formulation testing.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
We aim to support customers from initial product inquiry through formulation testing, sourcing decisions, and long-term supply cooperation — with consistent product quality and responsive communication.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
English English 
العربية
Deutsch
Українська
Ελληνικά
Español
Español de Perú
Français
Magyar
Bahasa Indonesia
Italiano
Português
Türkçe
Русский
Nederlands
Slovenčina
Svenska
Български
Čeština
Dansk
Eesti
Suomi
日本語
한국어
Lietuvių kalba
Latviešu valoda
Norsk bokmål
Polski
Português do Brasil
Română
Slovenščina
